haihongyuan.com
海量文库 文档专家
全站搜索:
您现在的位置:首页 > 幼儿教育 > 少儿英语少儿英语

焊接英文单词

发布时间:2013-09-18 10:21:08  

焊接工艺规程(WPS)

WELDING PROCEDURE SPECIFICATION

规程编号WPS No.

日期DATE

公司名称Company Name

依据的PQR编号Supporting PQR No.

签字人 BY (QA DIRECTOR)

生效日期Date

焊接方法 Welding Process MAG

自动化等级Type(s)Semi-Auto (Automatic,Manual,Machine,Semi-Auto.)

接头JOINTS

接头型式Joint Design

衬垫Backing (有/Yes) (无/NO)

垫块Retainers(有/Yes) (无/NO)

(Refer to both backing and retainers.)

衬垫材料(型号) Backing Material(Type) Base metal [ ]

金属Metal; [ ]

不熔化金属Non-fusing Metal; [ ]

非金属Non-metallic; [ ]

其它Other

Sketches,production drawings,weld symbols or written description should show the general arrangement of

The parts to be welded. Where applicable,the root spacing and the details of weld groove may be specified.

母材 BASE METALS

类别号P—No. 组号Group No. 1 与类别号to P—No. 组号Group No. 1 相焊, 或or

钢号/等级为Specification Type and Grade St52-3

与钢号/等级为to Specification Type and Grade St52-3 相焊, 或or

化学成分/力学性能为Chem.Analysis and Mech. Prop.

与化学成分和力学性能为 to Chem.Analysis and Mech. Prop. 相焊

厚度范围Thickness Range:

母材Base Metal:

坡口焊Groove 3~24mm

角焊Fillet not limited

管径范围Pipe Dia. Range:

坡口焊Groove Not Limitted

角焊Fillet not limited

其它Other

填充金属 FILLER METALS

SFA No. Special

AWS No.(Class) ANSI/AWS A5.18 ER70S-6

F—No. None

A--No. NA

填充金属尺寸 Size of Filler Metals Φ1.2mm

熔敷焊缝金属厚度范围 对接焊缝

Deposited Weld Met.Thickness Range: Groove max 24mm

角焊缝Fillet not limited

焊丝一焊剂Electrode-Flux (Class)

焊剂商标Flux Trade Name

熔化性嵌条Consumable insert

其 他 Other

焊接位置 POSITIONS

焊接位置sition (s) of groove

焊接方向Weld.Progression: 向上UP 向下Down

角焊缝位置 Position(s) of Fillet

预热 PREHEAT

最小预热温度 Preheat Temp. Min. 5 ℃

最大层间温度 Inter pass Temp. Max. 300℃

预热保持方式 Preheat Maintenance

(Continuous or special heating where applicable shall be recorded) 焊后热处理 POST-WELD HEAT TREATMENT

温度范围 Temperature Range

时间范围 Time Range

气体 GAS

百分组成 Percent Composition

气体Gas(es)

混合剂(Mixture)

流量Flow Rate

保护气 Shielding 二氧化碳+ 氩气 18/82 15-25L/min

尾部保护气Trailing

背面保护气Backing

电特性 ELECTRICAL CHARACTERISTICS

交流或直流 Current AC or DC DC

极性 Polarity EP

电流(范围) Amps(Range)

电压(范围) Volts(Range)

钨极尺寸和类型(纯钨极或2%钍钨极等) Tungsten Electrode Size and Type(Pure.Tungsten.2% thoriated.etc.)

金属过渡方式(射流或短路等) Mode of Metal Transfer for GMAW (Spray arc, short circuiting arc, etc.)

送丝速度范围 Electrode Wire Feed Speed Range NA

施焊技术 TECHNIQUE

无摆动焊或有摆动焊 String or Weave Bead String

喷孔或喷嘴尺寸 Orifice or Gas Cup Size

打底及中间焊道的清理方法(刷理或打磨等) Initial and Inter pass Cleaning(Brushing.Grinding.etc.) Grinding 磨

背部清根方法 Method of Back Gouging Carbon arc gouging 、 Grinding 碳弧气刨、磨

摆动方法 Oscillation

导电咀-工件距离 Contact Tube To Work Distance

多道焊或单道焊(每侧) Multiple or Single Pass (per side) Multiple 多道焊

多丝焊或单丝焊 Multiple or Single Electrodes

焊接速度(范围) Travel Speed(Range) See below

锤击有/无Peening None

其它 Other

焊层Weld Layers

焊接方法Process

填充金属Filler Metal

电流Current

电压范围Volt. Range

焊接速度范围Travel Speed Range

种类Class

直径Dia.

极性Type Polar

安培Amp.Range

1st side

1 MAG ER70S-6 Φ1.2mm DCEP 320-350A 32-34V 8-12cm/min

Others MAG ER70S-6 Φ1.2mm DCEP 320-350A 32-34V 8-12cm/min

2nd side

1 MAG ER70S-6 Φ1.2mm DCEP 320-350A 32-34V 8-12cm/min

Others MAG ER70S-6 Φ1.2mm DCEP 320-350A 32-34V 8-12cm/min 焊接工程师 日期 质保总监 日期 授权检验师 日期

PREPARED BY: DATE : APPROVED BY : DATE : ACCEPTED BY AI : DATE

网站首页网站地图 站长统计
All rights reserved Powered by 海文库
copyright ©right 2010-2011。
文档资料库内容来自网络,如有侵犯请联系客服。zhit326@126.com